Skip to content
Discuss Your Project
  1. Home
  2. Blog
  3. Dental operatory design: room size, clearances and floor utilities

Dental operatory design: room size, clearances and floor utilities

14 min read

Dental operatory design in Türkiye starts from area. A treatment room must be at least 12 m², have a hand basin and hold one dental unit. No width or depth is set. Two Henry Schein publications suggest about 2.9–3.05 m of width with side cabinets. The former rule (2016–2022) required 1.5 m at the patient's head end and 1 m elsewhere. With a sample chair, that is about 2.7 × 4.5 m.

Dental operatory design: what is the minimum room size?

In Türkiye a dental treatment room must be at least 12 m². The Regulation on Private Health Institutions Providing Oral and Dental Health Services calls it an examination room (muayene odası). It allows only one dental unit per room. The room has a hand basin and minimum equipment, and patient privacy is protected against sound, sight and noise.

The rule is written for dental practices in Article 8; examination rooms in polyclinics and centres follow the same standard (Art. 9/1-a, 10/1-a). ISO 4073 defines a dental unit as a combination of interconnected dental equipment and instruments forming a functional whole used during treatment. The operatory is the room that holds this unit, the patient and the treatment team.

SourceType of measureWidth × depthArea
Türkiye, regulation (since 6 October 2022)Minimum room area; no width or depth set—12 m²
Türkiye, former rule (2016–2022)1.5 m clear at the head end, 1 m on the other three sides; calculated with a sample chair2.71 × 4.46 m12.1 m²
US Department of Veterans Affairs (VA), multifunctional treatment roomNet room area—11.2 m²
VA, special needs treatment roomNet room area—14.0 m²
Henry Schein, community health centre guideRecommended room3.05 × 3.35 m10.2 m²
Henry Schein, same guideSimple room if necessary2.74 × 3.05 m8.4 m²
Dentsply Sirona, Sinius unitRecommended distances from the chair to a cabinet or wall2.55 × 2.66 m6.8 m²
Treatment room dimensions from Turkish rules, a US public standard, a distributor guide and a manufacturer document, as of November 2026. Feet and inches are converted to metres; areas in the Henry Schein and Dentsply Sirona rows are calculated from width × depth, and the former-rule row is Picco Architecture's sample calculation. Source: Ministry of Health of Türkiye, Regulation on Private Health Institutions Providing Oral and Dental Health Services, Art. 8, 2022; U.S. Department of Veterans Affairs, PG-18-9 Space Planning Criteria, Chapter 222, 2022; Henry Schein, CHC Planning Guide, 2017; Dentsply Sirona, Sinius installation requirements, 2018

These values do not measure the same thing. Türkiye gives a room size, the VA a net room area and Henry Schein a width and depth. Dentsply Sirona only shows the distances to leave from the chair axis to a cabinet or wall for installation. In our view, a manufacturer figure is therefore a lower bound; the basin, door and movement space come on top.

Area alone does not fix the shape. A square 12 m² room is about 3.46 × 3.46 m; a narrow one could be 2.4 × 5 m. In our view, width is the first dimension to check. Henry Schein's community health centre guide sets a 9 ft 8 in (about 2.95 m) minimum width for rooms with side cabinets.

The same distributor's ergonomics article builds the width from cabinet sizes. It puts the chair arm about 27 in (69 cm) from the side cabinet edge; the same distance suits the rear wall or cabinet. Cabinet fronts are 6.5–7 ft (1.98–2.13 m) apart and cabinets 15–18 in (38–46 cm) deep. From these, the article proposes a room 9.5–10 ft (2.90–3.05 m) wide, though the figures add up to 9–10 ft (2.74–3.05 m).

Depth depends on where instruments are delivered from. Henry Schein notes that some rear delivery systems need a deeper room. In Turkish centres that treat under general anaesthesia, each theatre holds a single unit or operating table. The theatre must be at least 30 m², with a short side of at least 5 m (Art. 10/1-c). We covered total clinic area and room sequence in our article on dental office floor plans.

How much clearance should be left around the dental chair?

Türkiye's current regulation sets no clearance around the chair. The rule in force from 2016 to 2022 required at least 1.5 m of working space at the patient's head end. On the other three sides it required at least 1 m. Today the unit maker's installation document sets the figure. For its Sinius unit, Dentsply Sirona recommends 1.45 m on one side of the chair axis and 1.10 m on the other.

The clearance rule entered the articles on dental practices, polyclinics and centres through an amendment of 23 December 2016. The original 2015 text had also required an examination room of at least 12 m². The new regulation, in force since 6 October 2022, dropped the clearances and returned to the 12 m² minimum.

Room width = 1.00 m + chair width + 1.00 m; room depth = 1.50 m + chair length + 1.00 m

VariableMeaning
1.50 mClearance at the patient's head end (2016–2022 rule)
1.00 mClearance on the other three sides
Chair width and lengthPlan dimensions of the chair with the backrest reclined, taken from the unit maker's installation drawing

Example: Midmark's CH-1000 chair, reclined, covers about 0.71 m in width and 1.96 m in length. Room width is 1.00 + 0.71 + 1.00 = 2.71 m and depth is 1.50 + 1.96 + 1.00 = 4.46 m. The area is about 12.1 m².

Method for calculating treatment room width, depth and area under the former Turkish clearance rule, in force from 23 December 2016 to 6 October 2022. Source: amending regulation in the Official Gazette of 23.12.2016, no. 29927 (2015 regulation, Art. 9, 10, 11); Midmark, Pre-Installation Information 003-10845-00, 2025; calculation by Picco Architecture.

The result is very close to today's 12 m². The difference lies in shape. With this chair the former rule required about 4.46 m of depth; the current rule also accepts a square room with 3.46 m sides. In the calculation the chair stands in for the unit; instrument and light arms may reach beyond it. The regulation draws no link between the two rules; the comparison is ours.

Manufacturer documents go into more detail. Midmark recommends 144.8–152.4 cm from the centre rear of the chair base to a 12 o'clock cabinet. Its light arm should sit 5.1 cm from the wall. Dentsply Sirona's drawing shows 410 mm from the centre of the floor opening to the wall at the foot end. With a tray or Heliodent Plus X-ray, this becomes at least 600 mm.

The same drawing warns that the swing range of the light, tray and X-ray arm exceeds the distance shown. In our view, walls should not be fixed before the unit model is chosen. If the model is still open, the former clearance rule and a width of about 3 m are a good check on the plan.

How do clock-face working zones shape the unit layout?

In the clock concept the patient's mouth is the centre of the dial and the head points to 12 o'clock. ISO 4073 draws four concentric circles (A, B, C, D) 0.5 m apart around the mouth. It divides the surroundings into 12 sectors like a clock face. Equipment positions are written with these coordinates: A8 means within 0.5 m in the 8 o'clock direction.

The pre-installation document that the Brazilian maker Alliage prepared for its Dabi Atlante unit assigns functions to these circles. It states that the 6–12 axis splits the room into two areas: the dentist's on one side and the assistant's on the other.

CircleDistance from the patient's mouthWhat it holds
A0–0.5 mTransfer zone: everything passed to the patient's mouth, instruments and handpieces; dentist and assistant stools
B0.5–1.0 mWidest working area reached with an outstretched arm: auxiliary tables and the unit body
C1.0–1.5 mOuter limit of the unit area: fixed cabinets and sinks; open drawers must fall inside circle B
D1.5–2.0 mLast circle in ISO 4073; the installation document gives it no separate function
Rings around the dental unit under the ISO 4073 circle system and the functions one manufacturer assigns to them; the patient's head points to 12 o'clock. Source: ISO 4073:2009, Dentistry — Information system on the location of dental equipment; Alliage, Dabi Atlante Versa pre-installation document

According to Henry Schein's ergonomics article, a right-handed clinician usually sits between 9 and 12 o'clock, mostly at 11 to 11:30. Citing a US survey, the article reports fewer back injuries at 11 to 11:30 than at 9 to 10. The article also sizes the room around the assistant's reach and motion, not the dentist's.

Fixed cabinets should sit within 1.5 m of the mouth, and open drawers within 1 m. The dentist's side needs room for the stool to turn freely between 9 and 12 o'clock. The assistant's side needs a short reach to the side cabinet.

The way instruments are delivered also changes the layout. Henry Schein lists three types: a single unit serving dentist and assistant, an over-the-patient unit above the chest, and a split system. In a split system the assistant's unit sits behind and the dentist's unit comes from the side wall or over the patient. In the article's view, delivery over the patient means less body rotation.

Which floor utilities does a dental unit need?

The floor connection point of a dental unit usually carries compressed air, clean water, suction (vacuum), waste water and power. A separate conduit serves data. Positions and sizes vary by manufacturer. ISO 7494-2 sets requirements for a unit's air, water, suction and waste water systems. In practice, the chosen unit's installation document gives the figures.

ConnectionDentsply Sirona, SiniusMidmark (CH-1000 chair and units)
Compressed air5.5–7.5 bar; at least 50 l/min; dew point −20 °C or lower; 10 × 1 mm pipe, 3/8 in angle valve80–100 psi (about 5.5–6.9 bar); 1/2 in pipe, 5 cm above the floor; shut-off valve; filtered, dry and oil-free air
Water2.5–6 bar; at least 3 l/min; softener if hardness exceeds 12 °dH; 10 × 1 mm pipe, 3/8 in angle valve40–60 psi (about 2.8–4.1 bar); 1/2 in pipe, 5 cm above the floor; shut-off valve
Suction (vacuum)0.12–0.18 bar vacuum; at least 500 Nl/min; DN40 pipe, inner diameter about 36.5 mmPiping specified by the central vacuum supplier; 3/4 in (1.9 cm) OD tube, 2.5 cm above the floor
Waste waterDN40 pipe, inner diameter about 36.5 mm; at most 3 l/minAt least 1 1/2 in (3.8 cm) ID to the trap, then 3/4 in (1.9 cm); 2.5 cm above the floor
Power and data3 × 1.5 mm² cable, at least 500 mm out of the floor; 16 A breaker at 230 V; data conduit at least 50 mm IDTop of the electrical box at most 11.4 cm above the floor; data conduit 2.5 cm above the floor
Position and heightCentre of the floor opening 269 mm from the foot end of the unit; air and water valves at most 60 mm above the floor, suction and drain flush with itConnections set out with the maker's floor template; the floor must support and anchor the chair
Floor connections of a dental unit according to two manufacturers' installation documents: pressure, flow, pipe size and position. Values are model-specific; psi values are converted to bar. Source: Dentsply Sirona, Sinius / Sinius CS / Sinius TS installation requirements, 05.2018; Midmark, Pre-Installation Information 003-10845-00, Rev AA3, 2025

The two manufacturers ask for the same connections at different sizes and pressures. Utility outlets should therefore not be set in the floor before the unit brand and the dentist's working side are decided. Dentsply Sirona asks for under-floor lines to be checked against an installation template.

Alliage asks for a 5–10% fall on the compressed air line in the flow direction, with an automatic drain valve at the lowest point. Waste lines need a 2–5% fall. It recommends 25 mm rigid PVC with 45° fittings for high-volume suction.

The floor must carry the unit's weight and anchoring forces. Dentsply Sirona requires a floor load capacity of at least 0.5 N/cm², about 500 kg/m². Screw points must resist pull-out forces above 1 kN.

How many dental units has Picco Architecture planned?

As of November 2026, Picco Architecture's project archive holds 124 dental projects with a recorded number of units. Of these, 120 are in Türkiye with 704 units in total, spread over 2015–2026 and 21 provinces. Abroad, three projects in Bishkek, Najaf and London and one in Iran add 15 units.

Of the units in Türkiye, 575 are in 95 polyclinics and 71 in 6 oral and dental health centres. Another 41 are in 18 dental practices and 17 in one dental hospital. The median is 5 units per project.

The 54 projects recorded in 2017–2021, with 300 units, fall in the period of the former clearance rule. The 47 projects recorded in 2023–2026 hold 261 units and fall in the 12 m² period. Our records hold no room dimensions, so none are given here for Picco projects.

For example, the Nanodent Oral and Dental Health Centre in Antalya is recorded as a 2021 project with 10 units and 1,300 m², delivered turnkey. See our healthcare projects for more.

Let’s discuss your dental clinic.

Leave a few details and our team will get in touch to discuss the scope, the budget and the next steps.

On-site surveys of existing premises are free of charge.

Prefer to talk now? WhatsApp Call Picco Architecture: +90 850 532 10 50

Type of facility
Do you have premises?
Contact Details
How did you hear about us? (Optional)

Please confirm that you have read the privacy notice to continue.

Frequently asked questions

Can two dental units share one room?

Not in Türkiye. The regulation allows no more than one dental unit per examination room, and rooms in polyclinics and centres follow the same standard. Two units therefore need two separate rooms of at least 12 m² each. Check the current rule with the provincial health directorate before applying.

Does an older treatment room under 12 m² lose its licence?

As a rule, no. Under provisional Article 1, amended on 15 December 2024, facilities licensed earlier follow the regulation in force on their licence date for physical requirements. There are exceptions. If a facility moves address, its pre-approval, licence and operating permit applications are made again. For major repairs and alterations, it applies to the directorate with municipality-approved revised plans (Art. 15/5, 15/10). Licensed physical areas cannot be changed without permission either. We covered licensing in our article on requirements to open a dental clinic.

How wide should the operatory door be?

Under Türkiye's Planned Areas Zoning Regulation, entrances to independent units (bağımsız bölüm) need a clear width of at least 1.00 m. Other doors need 0.90 m. Doors must be at least 2.10 m high. An operatory door normally falls in the second group. The regulation covers areas with an implementation zoning plan; a local zoning regulation may also apply. The dental regulation requires polyclinic doors to allow wheelchair transport but sets no figure. Henry Schein cites US accessibility rules: at least 32 in (about 81 cm), preferably 36 in (91 cm), of clear entrance for wheelchair-to-chair transfer. Check the current rules with the local authority.

What ceiling height does a dental operatory need?

Türkiye's Planned Areas Zoning Regulation sets an interior height of at least 2.60 m on occupied floors, excluding mezzanines. A local zoning regulation may also apply. A unit-mounted light can fit within this: in Dentsply Sirona's Sinius drawing, the light's highest point is 2.15 m above the floor. For a ceiling-mounted light, confirm load and height with its maker, and the current rules with the local authority.

Is a window required in a dental treatment room?

The dental regulation sets no window requirement; it asks for all areas to be suitably ventilated and adequately lit. The original 2015 text asked for examination rooms lit by daylight; that wording was removed in 2016. In the United States, the VA counts a view outside from treatment rooms as a way to lower patient stress. Check the current rule with the provincial health directorate.

Is the operatory planned differently for a left-handed dentist?

In our view, a left-handed dentist's working areas mirror a right-hander's across the 6–12 axis. Henry Schein says that if right- and left-handed dentists share the room, both sides of the chair need equal clearance. Manufacturers such as Midmark offer chair-mounted instruments that can be set up on either side. In our view, floor connections should wait for this decision.

Start dental operatory design from the chosen unit's installation drawing, chair clearances and utility point, not from area alone. To review your room and unit layout, please get in touch.