Dental sterilization room design: dirty-to-clean flow, size and services
Dental sterilization room design starts with a run of benches where used instruments move one way. They pass from dirty receiving to cleaning, inspection, packing, the autoclave and sterile storage. In Türkiye, the regulation does not require a separate room for a dental practice or polyclinic. An oral and dental health centre installs a central sterilization unit or buys the service; hospitals must have one. The regulation sets no size; seven rooms studied in Scotland had a median area of 7.6 m².
Is a separate sterilization room required in a dental clinic?
In Türkiye, the regulation sets no requirement for a dedicated sterilization room in a dental practice or polyclinic. The Regulation on Private Health Institutions Providing Oral and Dental Health Services sets a general duty instead. All premises, devices and consumables must meet disinfection and sterilization requirements (Art. 19/6). A separate unit is defined only for centres and hospitals.
A centre either installs a central sterilization unit for reusable items or buys sterilization as a service (Art. 10/1-d). The unit has three sections: soiled intake and washing, preparation and packing, and sterile storage and dispatch. Only materials may pass between preparation and sterile storage, and the two areas are divided by a double-door autoclave.
Where a single-door autoclave is used, it must stand in the preparation and packing area. A centre that outsources sterilization only needs separate sections for storing soiled and sterile items. A hospital must have the unit defined in Article 10 (Art. 11/1-d).
| Facility type | Sterilization requirement in the regulation | Separate room or unit | Article |
|---|---|---|---|
| Dental practice | All premises, devices and consumables meet disinfection and sterilization requirements | Not defined | Art. 19/6 |
| Polyclinic | Same general requirement | Not defined | Art. 19/6 |
| Oral and dental health centre | Three-section central sterilization unit; preparation and sterile storage divided by a double-door autoclave | Unit or outsourced service; if outsourced, separate storage for soiled and sterile items | Art. 10/1-d |
| Dental hospital | Central sterilization unit as defined in Article 10 | Mandatory | Art. 11/1-d |
The regulation adds two general rules for every facility. All areas are suitably ventilated, and floors in clinical units are easy to clean and disinfect (Arts. 7/1, 7/2). The minimum equipment list in Annex 4 is also mandatory (Art. 7/6). We cover the other rules for each facility type in our guide to opening a dental clinic. Confirm the current text with the provincial health directorate.
How are dirty and clean zones separated in a sterilization room?
Dirty and clean zones are separated either by a single bench run along which instruments always move forward, or by two rooms. England's Department of Health guidance HTM 01-05 requires that an instrument never touches a surface soiled at an earlier stage. Separation can be physical, or tasks in one area can be separated in time.
- Dirty receivingUsed instruments are placed on a set-down bench kept for this task only.
- CleaningWasher-disinfector or washing and rinsing sinks; ultrasonic pre-cleaning is optional.
- InspectionCleanliness, dryness and damage are checked on a well-lit clean bench; handpieces are lubricated if required.
- PackingFor a type B or S sterilizer, instruments are wrapped before sterilization.
- SterilizationThe autoclave stands on the clean side, away from other tasks.
- CoolingThe load is unloaded onto a separate, clean, well-lit area.
- Sterile storageInstruments are kept in closed cupboards where they cannot get wet.
The US Centers for Disease Control and Prevention (CDC) divides the instrument processing area into four sections in its 2003 dental guidelines. They are receiving, cleaning and decontamination; preparation and packaging; sterilization; and storage. CDC's ideal is a wall or partition between each section. Where that is not possible, adequate spacing may be acceptable if staff are trained.
HTM 01-05's preferred layout is one continuous line of sealed worktops that are simple to wipe down. The dirty receiving bench is used for nothing else, and the sinks or washer-disinfector sit next to it. The washer-disinfector may also stand by the rinse sink, away from receiving. Inspection needs a separate clean bench with good task lighting. The sterilizer stands well away from other activities and is unloaded onto another clean area.
Staff need a separate hand-wash basin, and instrument sinks should not be used for hand-washing. Under HTM 01-05, the basin has no plug or overflow, a trap set away from the plughole and a sensor or lever tap. Scotland's planning note requires two stainless steel sinks, each rectangular with its own drainer: one for washing instruments, the other for rinsing them.
For new premises or major alterations, HTM 01-05 recommends moving decontamination out of the treatment area. Its preferred option is two rooms: one for dirty work, one for inspection, sterilization and wrapping. A double-door washer-disinfector can be built into the dividing wall, or a transfer hatch can link the rooms. We discuss where sterilization sits in the clinic in our dental office floor plan guide.
Dental sterilization room design: how many square metres?
Türkiye's regulation gives no area for a sterilization room or unit. Scotland's SHPN 13 planning note also declines to set room dimensions. It sizes the room from the bench length of each component, maintenance access and workload. In one Scottish study, seven decontamination rooms had a median area of 7.6 m².
The study is by Smith and colleagues, published in the Journal of Hospital Infection in 2010. It surveyed 179 dental surgeries and measured rooms chosen at random. The seven rooms ranged from 2.9 to 16.0 m², and worktops took up 63% of the floor area on average.
The dental distributor Henry Schein, in its sterilization room guide, calls for at least 12 linear feet (about 3.66 m) of counter for 3–5 operatories. Larger practices need more. With the component lengths in the Scottish note, bench length can be worked out as follows:
Bench length = dirty-zone components + clean-zone components + hand-wash basin + records area
| Component | Length (m) |
|---|---|
| Dirty set-down area | 0.6 |
| Wash sink with draining board | 1.0 |
| Ultrasonic cleaner | 0.5 |
| Pre-rinse set-down area | 0.5 |
| Rinse sink with draining board | 1.0 |
| Post-rinse set-down area | 0.5 |
| Washer-disinfector (can sit under the bench) | 0.6 |
| Post-wash inspection area | 0.5 |
| Automated handpiece lubrication | 0.3 |
| Packing | 0.5 |
| Heat sealer | 0.5 |
| Pre-sterilization set-down area | 0.5 |
| Sterilizer | 0.6 |
| Post-sterilization cooling area | 0.6 |
| Water treatment unit (can sit under the bench or on a wall) | 0.6 |
| Hand-wash basin | 0.6 |
| Records area | 1.0 |
Example: one room and one sterilizer, with the washer-disinfector and water treatment under the bench and self-seal pouches. Dirty zone 0.6 + 1.0 + 0.5 + 0.5 + 1.0 + 0.5 = 4.1 m; clean zone 0.5 + 0.3 + 0.5 + 0.5 + 0.6 + 0.6 = 3.0 m. Total 4.1 + 3.0 + 0.6 + 1.0 = 8.7 m of bench and basin length; the door in Table A (0.9 m) is not included.
The 8.7 m in the example is more than twice Henry Schein's 3.66 m. In our view, the gap comes from the Scottish note giving each stage its own set-down area, plus two sinks and a records area. HTM 01-05 treats the ultrasonic cleaner as optional. SHPN 13 adds that self-seal pouches may make a heat sealer unnecessary.
If the bench does not fit on one wall, it can turn into an L or run along two facing walls. Henry Schein sees the galley layout as well suited to narrow rooms. SHPN 13 asks that no clean task sits above a dirty one, and that there is enough working space between facing benches.
What services do the autoclave and washer-disinfector need?
An autoclave needs distilled or demineralised water and a level bench strong enough for its weight. Manufacturers also recommend a dedicated or protected electrical circuit and, with frequent use, a heat-resistant drain connection. Values vary by model, so final figures come from the installation document of the chosen unit. The table below sets the documents of two manufacturers side by side.
| Installation data | Tuttnauer T-Edge 11 | Midmark M11 |
|---|---|---|
| Chamber | 27.2 l; about 28 cm diameter, 46 cm deep | 27.9 cm diameter, 45.7 cm deep |
| Electrical | 230 V, single phase, 1,960 W, 10 A | 230 V, 6.4 A |
| Circuit | 16 A breaker and residual current protection recommended | Dedicated circuit recommended |
| Water | Demineralised water, conductivity up to 15 µS/cm; optional 1/2 in automatic inlet | 5.3 l reservoir; access to the fill port kept clear |
| Drain | Optional 3/4 in, rated to 80 °C | Direct-to-drain recommended in enclosed areas with frequent cycles |
| Bench | At least 55 × 60 cm, rigid and level; 87 kg load | At least 55.4 × 67.3 cm, water-resistant and level; unit 44.9 kg |
| Wall clearance | About 15 mm at back and sides | 5.1 cm at back and sides, 12.7 cm above; at least 59.9 cm under a wall cabinet |
| Heat | Total under 200 Wh per hour | 5,275 kJ per hour in operation (about 1.47 kW) |
Steam sterilizers in dental clinics usually have a chamber under 60 litres, and HTM 01-05 treats them as small devices. The standards it describes define three types. Type N is for unwrapped solid instruments. Type B has a vacuum stage for hollow and wrapped loads, and type S handles loads defined by the manufacturer. According to HTM 01-05, types B and N are the ones English dental practices use most often.
For sterilizer water, HTM 01-05 recommends distilled or reverse osmosis water and refers feed-water quality to Annex C of EN 13060. Tuttnauer's manual lists those limits: conductivity up to 15 µS/cm and hardness up to 0.02 mmol/l. In our view, the room should include space for a water treatment unit; SHPN 13 allows 0.6 m for it.
For the washer-disinfector, SHPN 13 notes that an enhanced power supply may be needed and asks for drains that withstand 95 °C. Sockets sit at least 150 mm above the bench and are rated IP55, and the bench is lit to 500 lux. We advise against fixing water, drain and power outlets before the equipment models are chosen.
How should a sterilization room be ventilated?
Under English and Scottish guidance, air in a sterilization area moves from the clean side to the dirty side and is extracted there. Türkiye's regulation asks for suitable ventilation and air conditioning but gives no figures (Arts. 7/1, 7/3). The CDC also leaves room ventilation to manufacturer specifications and local building codes. Numerical reference values can be found in Scotland's SHPN 13.
| Model | Room | Supply (air changes/hour) | Extract (air changes/hour) | Room pressure |
|---|---|---|---|---|
| Single room | Sterilization room | At least 7 | 10 | Negative (chapter 4: not positive to adjoining areas) |
| Two rooms | Wash room | At least 7 | 10 | Negative |
| Two rooms | Sterilization room | At least 10 | 7 | Positive |
Where mechanical extract units are used, HTM 01-05 asks for them to be fixed to the ceiling or wall. Where the room is fully mechanically ventilated, the guidance sizes and positions the extract carefully. Roughly a third of the airflow should sweep over the benches, from the clean end towards the dirty end. The supply side has coarse filtration. Free-standing or ceiling fans are not recommended; through-wall fan units are often useful.
In a single-room unit, SHPN 13 places the extract grille near the sinks. One example is 600 mm above the worktop, between the wash and rinse sinks. Supply air passes a filter of at least class EU3; fresh air is at least 8 l/s per person. Room temperature is kept at 16–21 °C and relative humidity at 40–70%.
Example: a room of 7.6 m² with a 2.6 m ceiling holds about 19.8 m³. Ten air changes per hour mean about 198 m³/h of extract; seven mean about 138 m³/h of supply. Autoclave heat also counts. The two documents state it differently: under 200 Wh per hour in total, and about 1.47 kW in operation.
How does Picco Architecture plan sterilization in dental clinics?
Picco Architecture's project records include 122 dental facility projects in Türkiye: 96 polyclinics, 19 practices, 6 centres and 1 hospital. Of these, 115 are types for which the regulation sets no separate sterilization room. The other 7 are types for which today's regulation defines a central sterilization unit.
The 120 projects with a recorded unit count total 704 dental units, across 21 provinces and the years 2015–2026. Fifty of them have 3–5 units, the range of Henry Schein's 12-foot counter guidance. Forty have 6–10 units and 13 have 11 or more. The records do not include room sizes, so we do not attribute sterilization room sizes to our projects.
We draw sterilization close to the treatment rooms, away from the patient route, as one bench run that reads from dirty to clean. In our view, a new project should place sterilization in its own room even where the regulation does not require it. For scale, see our 17-unit MosDent Oral and Dental Health Hospital project and our healthcare projects.
Let’s discuss your dental clinic.
Leave a few details and our team will get in touch to discuss the scope, the budget and the next steps.
On-site surveys of existing premises are free of charge.
Prefer to talk now? WhatsApp Call Picco Architecture: +90 850 532 10 50
We have received your project enquiry.
Our team will review the information you shared and get in touch with you.
Frequently asked questions
Can instruments be sterilized inside the treatment room?
Türkiye's regulation does not say where a practice or polyclinic must process instruments. Under England's HTM 01-05 guidance, reprocessing in the treatment room should be as far from the dental chair as the room allows. Steps that create aerosols or splashes should not happen while a patient is present. Examples are manual washing, an ultrasonic cleaner without a lid and opening the machines. The guidance recommends a separate room in new premises.
Can a sterilization room have a window?
Türkiye's regulation sets no window rule for sterilization areas. The rule that windows must not open to the outside applies to the sterile areas of the general anaesthesia unit in centres and hospitals (Arts. 10/1-c, 11/1-c). Scotland's SHPN 13 asks for sealed windows that stay closed while the room is in use, with no internal ledges and no curtains.
What stays in the clinic if sterilization is outsourced?
The regulation addresses this for centres. A centre that buys sterilization as a service only needs sections where soiled and sterile items are stored separately (Art. 10/1-d). In our view, these sections should be apart from each other and off the patient route. For hospitals, the regulation makes a central sterilization unit mandatory.
Which floor and worktop finishes suit a sterilization area?
Under the regulation, floors in clinical units are easy to clean and disinfect (Art. 7/2). England's HTM 01-05 guidance asks for impervious flooring with welded or sealed joints, coved up to the wall. Worktops should be as jointless as possible. We cover surface choices in our small dental office design guide.
How long and where are sterile instruments stored?
Under England's HTM 01-05 guidance, wrapped instruments may be stored for up to one year. Unwrapped instruments may be kept for up to one day in the clinical area and up to one week in a clean non-clinical area. The CDC advises storing sterile items in closed or covered cabinets where possible, not under sinks or anywhere they might get wet.
Starting with the rules for your facility type, the choice of autoclave and washer-disinfector, and a bench length calculation reduces later changes to services. To review a plan for your number of units and your premises, get in touch with us.